Water Bottle Holder/Carrier Sewing Pattern

Water Bottle Holder/Carrier Sewing Pattern

My family and I appreciate climbing together, and as the mother, I commonly wind up being the “pack donkey” for our little gathering. One day I contemplated internally, “Why am *I* conveying the greater part of the water bottles?” Probably in light of the fact that I was conveying the main knapsack in the group…so I began feeling that I ought to make sense of how to get each of my children to in any event convey his own particular water bottle. In the wake of scanning online for an example to make some water bottle holders/transporters for my children to utilize, I in the long run added to my own particular mixture design in light of a portion of the thoughts I found.

Water Bottle HolderCarrier Sewing Pattern
Water Bottle HolderCarrier Sewing Pattern

Motivated generally by this example which uses old pants, furthermore the thought of fortifying the strap found in this example, my form results in a transporter which is a tiny bit bigger, has a more strong strap, uses a genuine pocket from a couple of pants, and is developed in a way which permits the greater part of the crude edges to be disguised. I made these for birthday presents for my nieces and nephew, and they were a gigantic hit! What’s more, the pocket is the ideal spot to put a trail guide when climbing!

(This example is the property of YarnThrower and may not be duplicated aside from one duplicate for individual use. On the off chance that you print or convey this example without YarnThrower’s composed consent, you are taking .)

Materials required:

4 feet of strapping/belting (appeared in the photograph as grayish in shading, however utilize whatever shading you’d like :- )

4 feet of grosgrain lace which is a marginally littler width than the strapping/belting material

9.5 x 11.5 inch bit of scrap fabric, cut along the grain line

9.5 x 11.5 inch bit of denim (can be cut from old pants), slice parallel to the grain line, to frame the “shell” of the water bottle holder/bearer. (I for the most part make a slice which goes through and through in one of the legs of the pair of pants, and afterward open it up/straighten it out to use as my fabric to cut the 9.5 x 11.5 inch piece)

Discretionary: Pocket painstakingly expelled from pair of old pants by cutting the strings which are holding it to the pants

Fundamental sewing supplies, for example, organizing string (I utilized white), sewing machine, scissors, needle, pins, and so on.

Initially, fixate the grosgrain strip on the strapping material and crisscross fasten along both side edges of the lace to secure it. I additionally crisscrossed along the short edges to keep them from raveling:

Here are the shell and covering fabrics effectively sliced to be 9.5 x 11.5 inches:

In the event that you are going to put a pocket on your transporter, line the pocket to the shell fabric so that the highest point of the pocket is parallel to one of the more drawn out edges of the shell fabric, thus that it is focused between the left and right sides of the shell fabric. Permit a space of around an inch between the highest point of the pocket and the upper edge of the shell fabric:

Next, fold the shell fabric down the middle, right sides together, so that the shorter sides of the shell fabric match. Line along the more drawn out side of the rectangle shaped in the wake of collapsing, making a container of fabric. Rehash with the coating fabric, EXCEPT leave an opening of 3″ amidst the crease:

In this next photograph, the zone between the purposes of the scissors is the spot where the crease of the covering has been left open for 3″:Next, alter the container of fabric with the goal that when smoothed, the crease which was sewn in the past step keeps running down along the middle, as appeared in the photograph beneath. Join along one of the finishes of the tube. On the off chance that you have sewn a pocket to the shell, ensure that you fasten along the edge of the fabric tube which is *closest* to the *bottom* of the pocket. Something else, the pocket will be upside-down on the completed item. (Ahem, don’t ask me how I know this.) Again, I generally crisscross fasten over the crude edges to keep them from raveling:

Presently, to add some profundity to the sack, fold it/pin it as appeared in this photograph. You will be sewing a straight line situated around one crawl far from each of the tips of the little triangles shaped by the collapsing. Confounding? Possibly these photos will offer assistance:

This is what it would seem that after it’s sewn:

Trim off the abundance little triangles and crisscross line over the edges to secure them (so they don’t disentangle):

The “shell” of the transporter is finished. It has a rectangular base and can just about stand up without anyone else’s input :- ) Leave it wrong side out and put it aside for the present:

Make a rectangular base for the covering utilizing the same system for sewing little triangles, trimming them, and securing the crude edges by sewing over the edges with a crisscross stitch.Turn the coating “right side out” when done. Here is the completed the process of covering. You can see where the opening is that will be utilized for turning later on:

Water Bottle HolderCarrier Sewing Pattern
Water Bottle HolderCarrier Sewing Pattern

Next, take the strap and stick the *right side* of the strap (which is the side the lace was sewn onto) to the *right* side of the shell, with crude edges even, and putting the strap *inside* the tube, as appeared in the photograph:

Presently, put the covering into the shell, right sides together, and coordinating crude edges. Join through all thicknesses utilizing 1/4″ crease remittance. Here I likewise crisscross sewed along the crude edges to secure them better. This photograph demonstrates to everything stuck together (before I sewed it):

Subsequent to sewing, haul lining fabric out of shell; notice the opening for turning in this photograph:

Turn sack right side out by pulling the strap and the denim shell through the gap in the coating:

Whip fasten the opening of the coating shut:

Tuck the coating inside, making a fresh level edge around the highest point of the sack as appeared and sticking the top edges set up to hold them in position for the following step:

Line around top of sack near upper edge, and again 1/4″ in from the edge:

What’s more, voila’ – your water bottle holder/bearer is done:

I trust you play around with this example! As usual, I’m keen on your considerations, proposals, and particularly any revisions you might have to the bearings I’ve given.

Add a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.